Eddystone User Group

Contact & Comments

You can contact the Eddystone User Group by writing to

Chris Pettitt
EUG Webmaster
12 Hennals Avenue, Webheath, Redditch, B97 5RX

Or by email g0eyo(at)blueyonder.co.uk

REGRETFULLY DUE TO MALICIOUS HACKING WE HAVE HAD TO DISABLE TO COMMENTS FACILITY ON THIS PAGE SO TO CONTACT US USE THE EMAIL ADDRESS ABOVE.  

 By far the best way of entering  into a dialogue with other Eddystone enthusiasts is to join the Eddystone User Groups.io forum. https://groups.io/g/EddystoneUserGroup Here you will find 400+ Eddystone enthusiasts and experts who can answer your questions and give advice.

 

0 Comments

« Older Comments
Newer Comments »

  1. dave carden says:
    October 16, 2018 at 17:43

    Hi

    I have an Eddystone S750 and matching S-meter which has been lying around in my shack for a long time. Bought this when first licenced in the early 1960s but could do to pass on to a collector. Still works OK but could do with some TLC. Serial No. L12368. Thought of putting on Ebay when I came across your site. Looking for the optimum way to sell on. Any help much appreciated.

    Dave, G3RIK

    1
  2. Ray Rosler says:
    October 15, 2018 at 23:05

    where can I obtain the following parts

    1 wave knob D3008
    2 chrome Handles 5826p
    1 flex coupler D1680
    1 coupler D3084
    1 L24 coil range 9

    2
  3. Ray Rosler says:
    October 5, 2018 at 20:08

    I have a Eddystone model 830/4 that requires lots of TLC. I am in need of a set of 9 crystals. Could you advise me the freq of each xtal

    4
    • chris says:
      October 5, 2018 at 20:45

      Have a look in the service manual you can download from the website. Chris G0EYO

      5
      • Ray Rosler says:
        October 13, 2018 at 18:02

        Thanks for the info.
        The following are the parts I need

        1 wave knob D3008
        2 chrome handles
        2 flexible couplers D1680
        1 coupler incr D3084
        1 mixer coil D3275 range 9

        6
  4. Mike DesChenes says:
    October 4, 2018 at 17:21

    Hi, I just picked up a beautiful Eddystone 990R but it needs to be restrung. I can not find anything that shows the proper arrangement of the string. Could you point me in the right direction?

    Cheers,
    Mike Deschenes

    7
    • chris says:
      October 5, 2018 at 16:53

      you can down load the service manual from the website https://eddystoneusergroup.org.uk/Manuals/Eddystone_990R_manual.pdf
      the maintenance section gives re-stringing instructions but no pictures. Also worth looking in the Restoration section there is a note on Eddystone dial drives which may be helpful. Finally good idea to join the Yahoo Eddystone User Group forum where help from members is often available. Chris G0EYO

      8
  5. ken roan says:
    September 30, 2018 at 23:40

    hi just purchased a 840b/c to remove cover does all knobs need removing from front,thanks ken

    9
    • chris says:
      October 2, 2018 at 22:19

      yes, have a look at the restoration section for helpful info on these sets. Chris G0EYO

      10
  6. Jon McDowell says:
    September 12, 2018 at 00:13

    Thanks Chris.

    I have joined the yahoo group and have found where to start the process.

    Thanks again

    11
« Older Comments
Newer Comments »