Eddystone User Group

Contact & Comments

You can contact the Eddystone User Group by writing to

Chris Pettitt
EUG Webmaster
12 Hennals Avenue, Webheath, Redditch, B97 5RX

Or by email g0eyo(at)blueyonder.co.uk

REGRETFULLY DUE TO MALICIOUS HACKING WE HAVE HAD TO DISABLE TO COMMENTS FACILITY ON THIS PAGE SO TO CONTACT US USE THE EMAIL ADDRESS ABOVE.  

 By far the best way of entering  into a dialogue with other Eddystone enthusiasts is to join the Eddystone User Groups.io forum. https://groups.io/g/EddystoneUserGroup Here you will find 400+ Eddystone enthusiasts and experts who can answer your questions and give advice.

 

0 Comments

« Older Comments
Newer Comments »

  1. David Murray says:
    November 28, 2015 at 16:31

    I would like to extend my grateful thanks to Richard Booth of Wadworth, below Doncaster (A60) for repairing my beloved Eddystone 840C . I’ m now able to pass the long winter nights tuning around the world as I do not have a TV. I refuse to pay £145 for that appalling rubbish and would not have one without a licence so I make do without. Thank you again Richard.

    1
  2. Paul Hughes says:
    November 24, 2015 at 11:12

    Hi guys, please could you remove the Eddystone 880/2 from the For Sale page as I have now sold it. Many thanks

    paul G4VQI

    2
  3. Geoff Wooster says:
    November 11, 2015 at 19:18

    Dear Sir, I am refurbishing an Eddystone All World Two. I have built the battery eliminator and refurbished the receiver and now have it working really, really well. I have always been interested in TRF’s. I have a slight problem. I cannot find any calibration curves for all the coils.Can you give me a pointer please as to where to look, I would love a set of charts, and if they are available on the www I probably would be able to print them off. Can you help me with this please? Yours hopefully, Geoff.

    3
    • chris says:
      November 13, 2015 at 22:17

      If you look on the restoration section of the technical folder the there is quite a selection of material on the restoration of the All World Two including some calibration charts. Are theset the sort of thing you are looking for? Chris G0EYO

      4
  4. Andrew Thomsa says:
    October 23, 2015 at 18:38

    Hello
    Can I place an advert on your site please?
    I have an Eddystone 358 which I would like to sell. It is in pretty good cosmetic conditon given its age; has the full 10 coil pack and the power unit. I haven’t used it for some time but it was working but with very low sensitivity and low audio output. It is very heavy so it would have to be buyer collects. I am just 10 minutes from junction 9 on the M40. I’m looking for £100.

    5
    • chris says:
      October 26, 2015 at 18:51

      yes you can. send me details via e mail address on here, photos help, describe condition whether working and complete, whether you would courier or require pick up only, Chris G0EYO

      6
  5. John Hendrie ZL1API says:
    October 12, 2015 at 05:23

    I have just obtained an Edystone radio mod. S640 .It is going to require quite a bit of restoration. I have been lucky enough to find An article by Gerry O’Hara and he has mentioned your wed site as a great place to find help.
    One thing I was looking for was the template to print the finger plate cover for the S640.
    Also having trouble finding a circuit diagram .
    Hope you can help.
    many thanks John ZL1API

    7
    • chris says:
      October 13, 2015 at 10:45

      John
      There is a huge amount of information on this website for the s640 including service manuals. Contact Ian Nutt on iandcnutt@msn.com he may be able to help you with a template. In the restoration section you will find images of templates if you wish to make your own. Have a good look around. Chris G0EYO

      8
  6. Max Cotton says:
    October 2, 2015 at 21:36

    I am looking for an IF / RF control knob for my EA12 Eddystone receiver, cash waiting. 73 Max M0GHQ

    9
« Older Comments
Newer Comments »